This article listed below involving How to Install a Bathtub is pretty much stimulating. Read on and make your own personal results.
Setting up a bath tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably difficult project. If the old tub is conveniently accessible, the job can move easily; if you have to open a wall to eliminate the old bathtub and position the new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and also embeded in the brand-new one. Ensure you have qualified on your own for the task as well as fit attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to consider employing one prior to you start. Chances are you may require an expert plumber to make tube links.
This post will help you install a new bathtub in your restroom if you have already purchased a new tub and don't need to change the arrangement of your previous water supply pipes.
Your tools and material checklist should consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited accessibility that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washing machines are in location in between the faucet and the sink. Secure the tap in place with the maker provided backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Tub
Using the two wood boards under its feet, place the tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 small points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the tub until the spirit level checks out level.
To set up faucets, fit all-time low of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the supply of water as well as examine all joints as well as new pipework for leaks as well as tighten them if needed. Fill the bathtub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub must wait till the bathtub has been used at the very least when as this will certainly resolve it right into its last placement.
Planning for the Installment
First of all, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to break an inflexible seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and fittings. They are marketed in tubes as well as cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealant can fracture rather early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very curious about Installing A Bathtub and I'm hoping you appreciated my entry. So long as you enjoyed reading our article if you please be sure to share it. Many thanks for your time. Kindly check up our site back soon.
About This